Defoamer Improves Flow, But Effect Is Temporary
A relatively small concentration of a defoamer can have a significant impact on the dynamics of multiphase flow within a pipe, but the effect is generally temporary.
Omar K. Matar, a professor of fluid mechanics in the Department of Chemical Engineering at the Imperial College London, presented the results of his study at a recent webinar presented by the Society of Petroleum Engineers’ Separations Technology Technical Section. Matar is also the director of the Transient Multiphase Flow consortium, a group of oil and gas operators that includes BP, Chevron, Petrobras, Statoil, Total, and design software houses.
The study came about after one of the members approached Matar to examine the changes that would occur if chemical additives were added to multiphase flow. “They were very interested in what would happen if we would add them to two-phase air/oil flow,” he said.
A chemical defoamer is a surfactant that lowers the surface tension of the interface between a fluid and a liquid. It destabilizes the film in between the bubbles and accelerates the coalescence of the bubbles. The reduction of the foam changes the dynamics of flow, the droplets, and the waves formed.
The specific chemical additive remains proprietary information. However, Matar said the results would apply to a wide range of defoamers. “We believe quite strongly that the results we see here are fairly generic,” he said.
“Higher surface tension tends to give you longer and longer waves,” he said. The study showed that the surfactant produces the opposite effect: It lowers surface tension, shortens the wave, and increases wave frequency.
Matar’s laboratory is equipped to look at a wide range of flow configurations (Fig. 1). He set up a continuous flow system that used high-speed cameras to document the effects of surfactants on the flow axially (down the pipe) and radially (from the side).
Looking down the length of the pipe, the video showed how the gas interacts with the liquid as they both flow through the pipe. The interaction of turbulent gas with the liquid below produces waves that emit droplets that are carried by the gas. Some of these droplets strike the sidewalls of the pipe and form a film, which gradually drains downward. “It’s a dynamic situation,” he said. “The flow configuration is reasonably simple, but the inherent nature of the flow is very complicated.”
The side view showed the formation of the waves as liquid and gas flow down the pipe. The experiment allowed Matar to plot surface tension (measured in millinewtons per meter) as a function of concentration (measured in parts per million) of the defoamer.
The tests showed that as the concentration of the defoamer increases, the surface tension generally declines. At some point, the surface tension reaches a point when it no longer falls. The tests were measured at relatively low levels at which the changes in the concentration of surfactant had a noticeable effect on surface tension, Matar said.
The tests also examined the effects of surfactant on the transition of different types of waves observed in the pipe: from slug flow to wavy and stratified flows.
Matar plotted the effects of the surfactant at various concentrations, starting at a baseline of no surfactant. He then gradually increased the surfactant to 5 ppm, then 25 ppm, and finally 50 ppm. He studied the effects of the different concentrations of defoamers on the types of waves that formed inside the tube.
The concentration has an effect on the type of waves that occur in the pipe. As the concentration of the surfactant increases, Matar noticed that the wave lengths become shorter and droplets form in the gas.
The increasing concentration of the defoamer also has an effect on the droplets that are carried in the gas stream. Once the defoamer is added to the flow, a few droplets begin to form. As the concentration increases, so too does the number of droplets.
Matar also noticed that when the model increases the speed of the gas in the pipe, the flow becomes more complex. The amplitudes of the waves become larger and the waves are three-dimensional in nature, even in the absence of a surfactant. As the concentration of surfactant increases, the presence of the droplets becomes more pronounced. Meanwhile, the thickness of the pool of liquid at the bottom of the pipe declines.
The results were informative. Other studies will likely examine the multiphase flow in vertical pipes and the effect of surfactants on them. “We hope this is the beginning of a long line of research,” he said.
A recording of this webinar can be viewed here.
Corinth Secures Subsea 7 Contracts for Aker BP Subsea Tiebacks
The steel pipe manufacturer agrees to deliver outer pipes for pipe-in-pipe flowlines for a pair of recently-announced Aker BP projects in the Norwegian Sea.
Executing Offshore Projects More Efficiently
Offshore project execution enhancement ideas are highlighted for debottlenecking, gas-hydrate-induced pipeline vibration, and the design of subsea systems for efficient startup.
Hydrate-Induced Vibration in an Offshore Pipeline
A computational fluid dynamics model is proposed to analyze the effect of hydrate flow in pipelines using multiphase-flow-modeling techniques. The results will identify the cause of pipeline failure, regions of maximum stress in the pipeline, and plastic deformation of the pipeline.
15 March 2018
22 February 2018
27 February 2018
26 February 2018